Search found 192 matches
- Mon May 31, 2021 4:10 am
- Forum: Application Notes and Design Ideas
- Topic: MOD5441X/NANO54415 PeriodicAD Example
- Replies: 6
- Views: 34512
Re: MOD5441X/NANO54415 PeriodicAD Example
Did this ever get itself worked into NBEclipse? I couldn't find an example file, only a header, but there wasn't much in there to go with.
- Thu Oct 08, 2015 10:31 am
- Forum: Off-Topic
- Topic: MOD54415 sending UDP packet from IRQ7 ISR routine
- Replies: 5
- Views: 16587
Re: MOD54415 sending UDP packet from IRQ7 ISR routine
Ok, I've got a few questions: Do you know the destination IP address when you create the IRQ7 packet? If you know the destination IP, do you also know the hardware MAC address? The problem with trying to just send a packet from your level 7 IRQ is that when it gets down to the bottom of the world, ...
- Thu Oct 08, 2015 6:55 am
- Forum: Off-Topic
- Topic: MOD54415 sending UDP packet from IRQ7 ISR routine
- Replies: 5
- Views: 16587
Re: MOD54415 sending UDP packet from IRQ7 ISR routine
How about setting up the packet ahead of time, so the irq7 only posts the semaphore, and your highest priority task is only a pend and send udp packet? An interrupt will call the scheduler, so after the irq7 returns, the highest task ready to run will run, so you do not have to wait for the task th...
- Wed Oct 07, 2015 7:10 pm
- Forum: Off-Topic
- Topic: MOD54415 sending UDP packet from IRQ7 ISR routine
- Replies: 5
- Views: 16587
MOD54415 sending UDP packet from IRQ7 ISR routine
I'm trying to do the impossible, the forbidden. I'm trying to send a tiny UDP packet from an IRQ7 interrupt function. I've created a circuit that raises the IRQ7 pin high when the circuit board voltage drops below a certain level (Undervoltage Lockout or UVLO). What I've been able to do in the inter...
- Wed Sep 16, 2015 7:15 am
- Forum: Off-Topic
- Topic: printf and float
- Replies: 2
- Views: 10333
Re: printf and float
Thanks Paul,
I must have had some form of typo in there. I deleted and retyped it and it worked. Thanks!
I must have had some form of typo in there. I deleted and retyped it and it worked. Thanks!
- Wed Sep 16, 2015 7:12 am
- Forum: NetBurner Software
- Topic: Accessing other I2C ports on MOD54415
- Replies: 14
- Views: 17617
Re: Accessing other I2C ports on MOD54415
I realize it's 2 years later, but has any of this been incorporated into the NNDK2.7.3? I need to use I2C 0 and I2C1 for a project and am hoping not to have to go through all these steps to use it... or change my board design.
- Tue Sep 15, 2015 8:50 am
- Forum: Off-Topic
- Topic: printf and float
- Replies: 2
- Views: 10333
printf and float
Not sure if this topic has been discussed before or not. I'm trying to output a double precision value to MTTTY. I'm getting weird numbers... volatile double numberz[16] numberz[0] = 5.01021; numberz[1] = 3.33205 /// etc up to index 15 for (int i = 0; i < 16; i++) printf("Output: %2.6f\r\n"...
- Tue Jan 13, 2015 8:48 am
- Forum: Off-Topic
- Topic: MOD5445 Eclipse 2.6.7 Debugger
- Replies: 2
- Views: 6721
Re: MOD5445 Eclipse 2.6.7 Debugger
Hi, thanks for responding, I did figure out the problem. There was a misconfigured interrupt, that's all. Thanks anyway!
- Mon Jan 05, 2015 11:18 am
- Forum: Off-Topic
- Topic: MOD5445 Eclipse 2.6.7 Debugger
- Replies: 2
- Views: 6721
MOD5445 Eclipse 2.6.7 Debugger
Hi all, Just wondering if someone could tell me if I'm missing something - I'm running the debugger and even though I have set breakpoints, the system is just running past them regardless. Does the debugger run at a different IP address than what is set in the unit? MY debug configuration is set cor...
- Mon Jan 05, 2015 11:07 am
- Forum: Off-Topic
- Topic: MOD54415 Task Monitor SizeLeft = ?
- Replies: 5
- Views: 8694
Re: MOD54415 Task Monitor SizeLeft = ?
That wasn't my only issue - it would freeze up at random points too and I'd get the TaskScan message in MTTTY just before it would reboot itself. But the freeze point became a bit sporatic - so it never froze in the same place all the time...